Zum Inhalt springen

Arduino nano Programmierung

Projekte und Tutorials für Arduino Foren StartHardware-Forum Arduino nano Programmierung

Ansicht von 6 Beiträgen - 1 bis 6 (von insgesamt 6)
  • Autor
    Beiträge
  • #8636 Antworten
    Jonas
    Gast

    Hallo,
    ich habe folgendes Problem. Ich bin noch sehr unerfahren in der Programmierung. Zur Zeit habe ich ein Schulprojekt indem ich einen Arduino Nano programmieren muss. Dieser wird mit einer Spule verbunden und soll eine einstellbare/regelbaren (eingebbar oder durch einen Poti) Anziehkraft liefern. Wie kann ich dies in der Programmierung umsetzen??

    #8639 Antworten
    Stefan Hermann
    Administrator

    Hallo Jonas,

    ich glaube, die Schwierigkeit liegt hier eher in der Schaltung. Eine Spule (oder ein Elektromagnet) benötigt ja einen ziemlich großen Strom. Hast du dafür schon eine Schaltung? Vielleicht mit einem Transistor (Normaler NPN oder besser noch Mos-FET, z.B. IRF640)? Und du brauchst noch eine Freilaufdiode. Hier ist so eine Schaltung, nur dass die Spule hier ein Schaltrelais ist. Da wäre natürlich nur deine normale Spule einzusetzen: Schaltrelais. Die oberen LEDs und die zwei Widerstände kommen dann natürlich weg. Das Poti musst du an Pin 9 anschließen. Und als Code nimmst du einfach das Beispiel AnalogInOutSerial aus dem Arduino Menü (Datei>Beispiele>03.Analog>AnalogInOutSerial) – Hilft dir das erstmal weiter?

    Liebe Grüße

    Stefan

    #8649 Antworten
    Jonas
    Gast

    Hallo Stefan,

    vielen Dank für deine Antwort und deine Hilfe. Bisher habe ich noch keine Schaltung. Leider finde ich den Code nicht, den du aus dem Arduino Menü meintest. Ich verwende bisher nur einen Arduino Nano und einen MOS-FET. Mein Projekt ist es ein Magnetschrauber/greifer zu konstruieren. Durch einen Motor und 2 Verbindungsplatte wird dieser gesichert. Durch eine Verlängerung mit Spule werden Motor und Verbindungsplatten verbunden. Vorne an der Verlängerung wird ein M4 Bit befestigt. Die Spule soll durch einen den Microcontroller einen Anzugsmoment liefern (regelbar und einstellbar) der eine Schraube anziehen kann. Und durch Ausstellen des Anzugsmoment diese wieder fallen lassen kann. Bei der Umsetzung und Programmierung fällt es mir schwierig, wie ich ein solche Schaltung/ Code umsetzn muss.

    Gruß Jonas

    #9693 Antworten
    Rolf
    Gast

    Mein Projekt:
    Ich plane den Bau einer Hühnerklappe. Meine Besonderheit ist diese über einen Schrittmotor Nema17 und Steppertreiber A4988 zu bewegen. Als Auslöser soll sowohl ein Lichtsensor als auch ein Zeitschaltmodul dienen. Da Ganze natürlich mittels Arduino (Nano?)

    Meine Frage ist einfach nur ob so etwas bereits existiert.

    #26335 Antworten
    Pickl.AI
    Gast

    Well, now is the time to join hands with the industry’s best and most acclaimed Data Science Job Guarantee Course by Pickl. In this 120-hour course, along with one month of project experience, you become ready to make a professional start. Connect with Pickl.AI today.
    Know more: https://picklai.blogspot.com/2023/06/level-up-your-data-science-skills.html

    #26568 Antworten
    JamesSmith
    Gast

    Hello, I am a representative of altamira.ai, a company that develops
    software development
    I will help you with your question.

    To implement adjustable/controlled gravity using an Arduino Nano connected to a coil, you can follow these steps:

    Set up the hardware: Connect the coil to the Arduino Nano. Make sure that all the necessary wires and components are connected, such as the power supply, transistor or driver circuit (if needed), and any other components specific to your coil.

    Initialize the Arduino pins: In your Arduino program, you will need to initialize the pins you are using to control the coil. For example, if you are using a digital pin for control, you can set it as an output using the pinMode() function.

    Read the input to adjust the strength: If you want to provide adjustable force, you need to determine how the user will input the desired force. You mentioned two options: inputting a force or using a potentiometer. Depending on the method you choose, you can use digital or analog input contacts to read the input values, respectively.

    For force input: You can use the digital input pin and implement a method to read the desired force value using the keypad, buttons, or any other input device of your choice. For example, you can use the digitalRead() function to read the status of the digital input and adjust the force accordingly.

    Using a potentiometer: Connect a potentiometer to the analog input. Use the analogRead() function to read the value from the potentiometer. Match the analog value to the desired force range.

    Control the coil: Based on the input value obtained in the previous step, you can control the coil to provide the desired magnetizing force. Depending on the specific requirements of your coil, you may need to use a driver circuit or transistor to control the coil current.

    If you are using a digital pin for control, you can use the digitalWrite() function to set the pin HIGH or LOW, controlling the coil accordingly. If the coil needs more power than the Arduino pin can provide, you may need a transistor or driver circuit to increase the current.

    If you are using the analog pin for control, you can use the analogWrite() function to generate a PWM (pulse width modulation) signal. This can be used to control the power of the coil by changing the duty cycle of the PWM signal.

    Calculate the required force: Depending on the specific requirements of your project, you may need to calculate the force based on the input values. This may involve mapping the input range to a desired force range or applying a mathematical formula to determine the force. To do this, you can use variables, math operations, and conditional statements in your Arduino program.

    Remember to test and iterate your code, making adjustments based on the coil’s behavior and the desired output force. Also make sure you follow proper safety precautions when working with electrical components.

Ansicht von 6 Beiträgen - 1 bis 6 (von insgesamt 6)
Antwort auf: Antwort #8639 in Arduino nano Programmierung
Deine Information: