Zum Inhalt springen

LED Brückenlampe

  • Dieses Thema hat 4 Antworten und 1 Teilnehmer, und wurde zuletzt aktualisiert vor 2 Jahre von Antonio.
Ansicht von 5 Beiträgen - 1 bis 5 (von insgesamt 5)
  • Autor
    Beiträge
  • #8285 Antworten
    Stephan Götz
    Gast

    Hallo Ihr Lieben,

    Da ihr mir schon einmal so Toll geholfen habt, wende ich mich gleich wieder an euch!

    Es gibt ein Problem mit folgendem Sketch:

    [code]
    /*Led Bridge lamp code v1b
    Led strip is WS2811, data wire is on pin 2
    Standart rotary encoder
    Janis Jakaitis 03.08.2016
    absolutelly no varranty of any kond, use ta your won risk
    GPL licence
    */

    #include <Encoder.h>
    #include <NeoPixelBus.h>
    #include <EEPROM.h>

    //configuration
    const uint8_t PixelPin = 2;
    const uint8_t encButtonPin = 4;
    const uint16_t PixelCount = 119;

    //objects
    Encoder myEnc(5, 6);
    NeoPixelBus<NeoGrbFeature, Neo800KbpsMethod> strip(PixelCount, PixelPin);

    //variables
    uint8_t oldPosition = 0;
    int buttonState = 0;
    bool waitingForPress = true;
    bool waitingForRelease = false;
    bool confRGBIDone = false;
    bool confRGBInprogress = false;
    int confRGBIparamater = 0;
    int confR = 255;
    int confG = 255;
    int confB = 255;
    int confI = 255;
    long newPosition = 0;
    RgbColor curentColor(0, 0, 0);

    void setup() {
    Serial.begin(9600);
    Serial.println(“Basic Encoder Test:”);

    //setup encoder
    pinMode(encButtonPin, INPUT);
    myEnc.write(255);

    //read RGBI values from EEPROM
    confR = EEPROM.read(0);
    confG = EEPROM.read(1);
    confB = EEPROM.read(2);
    confI = EEPROM.read(3);

    //display stored values
    Serial.print(“EEPROM values R:” );
    Serial.print(confR );
    Serial.print(” / G:” );
    Serial.print(confG );
    Serial.print(” / B:” );
    Serial.print(confB );
    Serial.print( ” / I: ” );
    Serial.println(confI );

    //set strip to original color
    RgbColor curentColor(confR, confG, confB);
    strip.ClearTo(curentColor);
    strip.Show();

    }

    void loop() {

    if (confRGBInprogress == true) {
    newPosition = myEnc.read();
    if (newPosition != oldPosition) {

    //limit encoder values 0 to 2550
    if (newPosition > 255) {
    myEnc.write(255);
    newPosition = 255;

    curentColor = RgbColor(0, 0, 0);
    strip.ClearTo(curentColor);
    strip.Show();
    delay(300);
    curentColor = RgbColor(confR, confG, confB);
    strip.ClearTo(curentColor);
    strip.Show();

    }
    if (newPosition < 0) {
    curentColor = RgbColor(0, 0, 0);
    strip.ClearTo(curentColor);
    strip.Show();
    delay(300);
    curentColor = RgbColor(confR, confG, confB);
    strip.ClearTo(curentColor);
    strip.Show();
    myEnc.write(0);
    newPosition = 0;
    }

    oldPosition = newPosition;
    Serial.println(newPosition);

    // change colors on the fly according to encoder values
    switch (confRGBIparamater) {
    case 1:
    curentColor = RgbColor(newPosition, confG, confB);
    strip.ClearTo(curentColor);
    break;
    case 2:
    curentColor = RgbColor(confR, newPosition, confB);
    strip.ClearTo(curentColor);
    break;
    case 3:
    curentColor = RgbColor(confR, confG, newPosition);
    strip.ClearTo(curentColor);
    break;
    default:
    break;
    }
    strip.Show();
    }
    }

    // read encoder button press
    buttonState = digitalRead(encButtonPin);

    //wait for button to go LOW
    if (waitingForPress == true) {
    if (buttonState == LOW) {
    waitingForPress = false;
    waitingForRelease = true;
    // Serial.println(“Press” );
    }
    }

    // button goes HIGH after LOW = begin strip config
    if (waitingForRelease == true) {
    if (buttonState == HIGH) {
    // Serial.println(“Relese” );
    waitingForPress = true;
    waitingForRelease = false;
    confRGBInprogress = true;

    proceed according to button press counts
    switch (confRGBIparamater) {
    case 0:
    Serial.println(“Config, set red” );
    myEnc.write(confR);
    curentColor = RgbColor(255, 0, 0);
    strip.ClearTo(curentColor);
    strip.Show();
    delay(500);
    curentColor = RgbColor(confR, confG, confB);
    strip.ClearTo(curentColor);
    strip.Show();
    break;
    case 1:
    Serial.println(“Set green” );
    curentColor = RgbColor(0, 255, 0);
    strip.ClearTo(curentColor);
    strip.Show();
    delay(500);
    curentColor = RgbColor(confR, confG, confB);
    strip.ClearTo(curentColor);
    strip.Show();
    confR = +newPosition;
    myEnc.write(confG);
    break;
    case 2:
    Serial.println(“Set blue” );
    curentColor = RgbColor(0, 0, 255);
    strip.ClearTo(curentColor);
    strip.Show();
    delay(500);
    curentColor = RgbColor(confR, confG, confB);
    strip.ClearTo(curentColor);
    strip.Show();
    confG = +newPosition;
    myEnc.write(confB);
    break;
    /* case 3:
    * // intensidty code is nobready
    Serial.println(“Set intenisty” );
    curentColor = RgbColor(255, 255, 255);
    strip.ClearTo(curentColor);
    strip.Show();
    delay(500);
    curentColor = RgbColor(confR, confG, confB);
    strip.ClearTo(curentColor);
    strip.Show();
    confB = +newPosition;
    myEnc.write(confB);
    */
    case 3:
    Serial.println(“Done config” );
    curentColor = RgbColor(255, 255, 255);
    strip.ClearTo(curentColor);
    strip.Show();
    delay(500);
    curentColor = RgbColor(confR, confG, confB);
    strip.ClearTo(curentColor);
    strip.Show();
    confB = +newPosition;
    confRGBIparamater = 0;
    myEnc.write(confI);
    confRGBIDone = true;
    break;
    default:
    break;

    }

    // save data to EEPROM
    if (confRGBIDone == true) {
    //reset loop flags
    confRGBIDone = false;
    confRGBInprogress = false;
    confRGBIparamater = 0;
    // save to EEPROM
    EEPROM.write(0, confR);
    EEPROM.write(1, confG);
    EEPROM.write(2, confB);
    EEPROM.write(3, confI);
    //display
    Serial.print(“EEPROM saved R:” );
    Serial.print(confR );
    Serial.print(” / G:” );
    Serial.print(confG );
    Serial.print(” / B:” );
    Serial.print(confB );
    Serial.print( ” / I: ” );
    Serial.println(confI );
    }
    else
    {

    confRGBIparamater++;

    }

    }

    }

    }
    [/code]

    In Zeile 145 kommt folgende Meldung:
    exit status 1
    ‘proceed’ was not declared in this scope

    ich hoffe ihr könnt mir mal wieder helfen

    Grüße Stephan

    #8286 Antworten
    Stefan Hermann
    Verwalter

    Hi Stephan,

    das ist ein Easy-fix. Scheinbar hast du in dieser Zeile (145) nur den Doppel-Slash // gelöscht. Wenn man ihn dort einfügt, läuft der Code wieder.

    Liebe Grüße

    Stefan

    /*Led Bridge lamp code v1b
    Led strip is WS2811, data wire is on pin 2
    Standart rotary encoder
    Janis Jakaitis 03.08.2016
    absolutelly no varranty of any kond, use ta your won risk
    GPL licence
    */
    
    #include <Encoder.h>
    #include <NeoPixelBus.h>
    #include <EEPROM.h>
    
    //configuration
    const uint8_t PixelPin = 2;
    const uint8_t encButtonPin = 4;
    const uint16_t PixelCount = 119; 
    
    //objects
    Encoder myEnc(5, 6);
    NeoPixelBus<NeoGrbFeature, Neo800KbpsMethod> strip(PixelCount, PixelPin);
    
    //variables
    uint8_t oldPosition  = 0;
    int buttonState = 0;
    bool waitingForPress = true;
    bool waitingForRelease = false;
    bool confRGBIDone = false;
    bool confRGBInprogress = false;
    int confRGBIparamater = 0;
    int confR = 255;
    int confG = 255;
    int confB = 255;
    int confI = 255;
    long newPosition = 0;
    RgbColor curentColor(0, 0, 0);
    
    void setup() {
     Serial.begin(9600);
     Serial.println("Basic Encoder Test:");
    
     //setup encoder
     pinMode(encButtonPin, INPUT);
     myEnc.write(255);
    
     //read RGBI values from EEPROM
     confR = EEPROM.read(0);
     confG = EEPROM.read(1);
     confB = EEPROM.read(2);
     confI = EEPROM.read(3);
    
     //display stored values
     Serial.print("EEPROM values R:" );
     Serial.print(confR );
     Serial.print(" / G:" );
     Serial.print(confG );
     Serial.print(" / B:" );
     Serial.print(confB );
     Serial.print( " / I: " );
     Serial.println(confI );
    
     //set strip to original color
     RgbColor curentColor(confR, confG, confB);
     strip.ClearTo(curentColor);
     strip.Show();
    
    }
    
    void loop() {
    
     if (confRGBInprogress == true) {
       newPosition = myEnc.read();
       if (newPosition != oldPosition) {
    
         //limit encoder values 0 to 2550
         if (newPosition > 255) {
           myEnc.write(255);
           newPosition = 255;
    
             curentColor = RgbColor(0, 0, 0);
             strip.ClearTo(curentColor);
             strip.Show();
             delay(300);
             curentColor = RgbColor(confR, confG, confB);
             strip.ClearTo(curentColor);
             strip.Show();
    
         }
         if (newPosition < 0) {
             curentColor = RgbColor(0, 0, 0);
             strip.ClearTo(curentColor);
             strip.Show();
             delay(300);
             curentColor = RgbColor(confR, confG, confB);
             strip.ClearTo(curentColor);
             strip.Show();
           myEnc.write(0);
           newPosition = 0;
         }
    
         oldPosition = newPosition;
         Serial.println(newPosition);
    
         // change colors on the fly according to encoder values
         switch (confRGBIparamater) {
           case 1:
             curentColor = RgbColor(newPosition, confG, confB);
             strip.ClearTo(curentColor);
             break;
           case 2:
             curentColor = RgbColor(confR, newPosition, confB);
             strip.ClearTo(curentColor);
             break;
           case 3:
             curentColor = RgbColor(confR, confG, newPosition);
             strip.ClearTo(curentColor);
             break;
           default:
             break;
         }
         strip.Show();
       }
     }
    
    // read encoder button press
     buttonState = digitalRead(encButtonPin);
    
     //wait for button to go LOW
     if (waitingForPress == true) {
       if (buttonState == LOW) {
         waitingForPress = false;
         waitingForRelease = true;
         // Serial.println("Press" );
       }
     }
    
     // button goes HIGH after LOW = begin strip config
     if (waitingForRelease == true) {
       if (buttonState == HIGH) {
         // Serial.println("Relese" );
         waitingForPress = true;
         waitingForRelease = false;
         confRGBInprogress = true;
    
    //    proceed according to button press counts
         switch (confRGBIparamater) {
           case 0:
             Serial.println("Config, set red" );
             myEnc.write(confR);
             curentColor = RgbColor(255, 0, 0);
             strip.ClearTo(curentColor);
             strip.Show();
             delay(500);
             curentColor = RgbColor(confR, confG, confB);
             strip.ClearTo(curentColor);
             strip.Show();
             break;
           case 1:
             Serial.println("Set green" );
             curentColor = RgbColor(0, 255, 0);
             strip.ClearTo(curentColor);
             strip.Show();
             delay(500);
             curentColor = RgbColor(confR, confG, confB);
             strip.ClearTo(curentColor);
             strip.Show();
             confR = +newPosition;
             myEnc.write(confG);
             break;
           case 2:
             Serial.println("Set blue" );
             curentColor = RgbColor(0, 0, 255);
             strip.ClearTo(curentColor);
             strip.Show();
             delay(500);
             curentColor = RgbColor(confR, confG, confB);
             strip.ClearTo(curentColor);
             strip.Show();
             confG = +newPosition;
             myEnc.write(confB);
             break;
          /* case 3:
           *  // intensidty code is nobready
             Serial.println("Set intenisty" );
             curentColor = RgbColor(255, 255, 255);
             strip.ClearTo(curentColor);
             strip.Show();
             delay(500);
             curentColor = RgbColor(confR, confG, confB);
             strip.ClearTo(curentColor);
             strip.Show();
             confB = +newPosition;
             myEnc.write(confB);
            */
           case 3:
             Serial.println("Done config" );
             curentColor = RgbColor(255, 255, 255);
             strip.ClearTo(curentColor);
             strip.Show();
             delay(500);
             curentColor = RgbColor(confR, confG, confB);
             strip.ClearTo(curentColor);
             strip.Show();
             confB = +newPosition;
             confRGBIparamater = 0;
             myEnc.write(confI);
             confRGBIDone = true;
             break;
           default:
             break;
    
         }
    
    // save data to EEPROM
         if (confRGBIDone == true) {
           //reset loop flags
           confRGBIDone = false;
           confRGBInprogress = false;
           confRGBIparamater = 0;
           // save to EEPROM
           EEPROM.write(0, confR);
           EEPROM.write(1, confG);
           EEPROM.write(2, confB);
           EEPROM.write(3, confI);
           //display
           Serial.print("EEPROM saved R:" );
           Serial.print(confR );
           Serial.print(" / G:" );
           Serial.print(confG );
           Serial.print(" / B:" );
           Serial.print(confB );
           Serial.print( " / I: " );
           Serial.println(confI );
         }
         else
         {
    
           confRGBIparamater++;
    
         }
    
       }
    
     }
    
    }
    #8287 Antworten
    Stephan Götz
    Gast

    Danke Stefan!!!

    Ich muss schon sagen!!! DU BIST ECHT EIN GENIALER HAMMER!!!

    #8288 Antworten
    Stefan Hermann
    Verwalter

    :-)

    #8340 Antworten
    Antonio
    Gast

    Hallo guten Abend an alle,
    ich hätte ein Wunsch ist jemand der mir helfe möchte?
    ich habe das Projekt Led Brücke übernommen und nach gebaub
    aber ich glaube der Encoder trotzdem viel gegoogelt ich kann
    das nicht richtig anschließen (ich habe der Pin minus an minus angeschlossen, DT am 5 von Arduino und CLK am 6
    am Arduino, der Taster an minus und am Pin4 von Arduino und die Led Strip am Pin 2, ja es blinkt zwar dann macht Pause, wenn ich der Taster Drücke passiert nichts und wenn ich der Encoder drehen dann erscheint
    kurz eine Farbe und dann wird wieder weiß,
    ich würde mich sehr freuen wenn jemand mir helfen kann.
    Ich bedanke mich in voraus und verbleibe.
    Mit freundlichen Grüßen
    Antonio

Ansicht von 5 Beiträgen - 1 bis 5 (von insgesamt 5)
Antwort auf: Antwort #8340 in LED Brückenlampe
Deine Information: